24" 6.5 CREEDMOOR & 18" 308 WIN CUSTOM DPMS AR10 SYSTEM GEN 2 STORM TROOPER WHITE

24" 6.5 CM & 18" 308 CUSTOM DPMS AR10 SYSTEM GEN 2 BRUSHED STORM TROOPER WHITE

Please Read Full Description of the Product and FAQ Page. All Purchases are subject to all terms and conditions.. 

BILLET UPPER:

·       US made in Scottsdale, Arizona

·       T6061 billet

·       1913 picatinny rail flat top-DPMS low spec rail height

·       manufactured from solid block of billet aluminum

·       Brushed Camo Gun Metal Gray Cerakote

·       slim profile shell deflector / forward assist

·       308 WIN engraved dust cover

·       6.5 CREEDMOOR engraved dust cover on CREEDMOOR upper

6.5 CREEDMOOR BARREL:

·       24” MATCH GRADE straight fluted bull barrel

·       0.936” Gas Block

·       RIFLE length gas tube

·       Straight fluted for maximum heat dissipation

·       416R STAINLESS STEEL

·       5/8x24 muzzle thread pitch

·       1:8 TWIST

·       M4 feed ramp

308 WIN BARREL:

·       18” MATCH GRADE HBAR barrel

·       0.75” Gas Block

·       MID LENGTH length gas tube

·      416R STAINLESS STEEL

·       5/8x24 muzzle thread pitch

·       1:10 TWIST

·       M4 feed ramp

6.5 CREEDMOOR HANDGUARD:

·       16.5” Super slim Handguard

·       Brushed Camo Gun Metal Gray Cerakote

·       T-markings on top rail

·       Ultra-Light weight

308 WIN HANDGUARD:

·       15” Super slim Handguard

·       MLOK SYSTEM with three sectional rails installed

·       Brushed Camo Gun Metal Gray Cerakote

·       T-markings on top rail

·       Ultra-Light weight

BOLT CARRIER GROUP:

·       Made for 7.62X51 / 308 Cal & 6.5 CREEDMOOR

·       HPT/MPI Tested and Marked

·       9310 Hardened Steel Bolt

·       17-4 Stainless Steel Firing Pin (Heat treated to H900 Condition)

·       8620 carrier and gas key.

·       Hardened extractor S7 tool steel.

·       The group comes fully assembled with properly torqued and staked gas key

·       Made in the USA

**  Nitride bolt carrier

(One BCG is included with the AR10 package)

6.5 CREEDMOOR MUZZLE BRAKE:

·       TANKER style

·       TOP ports for MUZZLE CLIMB REDUCTION

·       SIDE ports for RECOIL REDUCTION

308 WIN MUZZLE BRAKE:

·       Slip over sleeve style

·       side ports for recoil reduction

BILLET LOWER RECEIVER:

·       Machined from 7075-T6 aircraft grade billet aluminum

·       Matte black hard-coat anodized per Mil 8625 Type 3 Class 2

·       Precision broached magazine well with beveled feed lips

·       Machined and engraved to be compatible with 45 and 60-degree short throw fire control selectors.

·       Caliber marking of “Multi” so it can be used with many different caliber uppers

·       Compatible with all standard AR-10/.308 components and magazines and most aftermarket parts — Made to DPMS spec

·       Upper tension screw behind grip screw (threaded hole with hardware included) to adjust any “slop” out of vertical fit between upper and lower

·       Ambidextrous trigger finger rests with grooves (above and below mag release / mag catch)

·       Brushed Camo Gun Metal Gray Cerakote

·       Threaded bolt catch pin (Threaded hole and hardware)

·       Integrated large opening “winter” trigger guard

·       Manufactured to MILSPEC on state-of-the-art CNC equipment for consistent quality parts and exacting tolerances

Due to COVID 19 the material supply chains have been extremely depleted. The depletion of materials is causing a huge delay in manufacturing and production. Current lead times are running a MINIMUM of 12-15 weeks for all AR10 lower receivers. Demand is increasing daily; we recommend that if you do want a product to go ahead and reserve yours on backorder now. As for now, we are not sure when the material supply chains will be operating at full force again.

STANDARD MILSPEC TRIGGER:

LUTHAR MBA3 STOCK:

·       Fully adjustable carbine buttstock assembly to mount to a carbine rifle (6-positions mil-spec or commercial tube) – this is our carbine stock

·       additional 1″ height on cheek rest

·       3-axis adjustable butt plate assembly extends additional 1 1/16″ length of pull and includes the following movement:

1.     horizontal for linear adjustment (i.e. length of pull)

2.     vertical for a perfect butt plate fit into the curvature of the shoulder.

3.     lateral adjustment for a ½ inch left or right cast

4.     this butt plate assembly is interchangeable with the original mba-1 buttstock

·       Includes a picatinny rail on the bottom rear of the stock body to attach your choice of many accessories.

·       Designed a flat bottom index set screw (10-24) to eliminate that constant rattle of carbine collapsible buttstock. this also allows you to secure the stock in your favorite position.

·       The black mba-3 comes with a medium soft rubber recoil pad, duro 85.

·       The LUTHAR mba-3 weighs roughly half that of comparable stocks coming in at just 18.5 ounces.

·       Fits all .223 and most .308 AR carbine style rifles

·       Super strong glass filled nylon

·       Easy to replace and quick to install

·       Uses 4 out of the 6 positions on a mil-spec or commercial tube

FEATURES:

·       ergonomic

·       adapts to existing commercial and mil-spec buffer tubes

·       certain aftermarket commercial buffer tubes that exceed 1.172″ may not fit

·       the vertical struts for the MBA 3 are fixed therefore the cheek pc is not reversible like the MBA 1 however the cheek piece itself is designed with a cheek pad for the lefty

44” Flight Case:

·         Made from tough light-weight polypropylene copolymer

·         Has a rugged o-ring seal that makes it air and water tight up to 3ft deep

·         Custom laser cut foam to hold all components fo the system firm in place and provide maximum protection.

·         Utilize an automatic pressure release valve so that it adjusts to its environment

·         ATA/TSA ready for airline travel

·         Lockable with comfort molded handles and spring loaded latches

·         include heavy-duty off-road wheels and a second handle. 

·         Made in the USA

Vortex Crossfire II 3-24x50 Scope:

OPTICAL FEATURES:

·         Fully Multi-Coated  Increases light transmission with multiple anti-reflective coatings on all air-to-glass surfaces.

·         Second Focal Plane Reticle           Scale of reticle maintains the same ideally-sized appearance. Listed reticle sub tensions used for estimating range, holdover and wind drift correction are accurate at the highest magnification.

·         Illuminated Center Dot Provides a precise aiming point under low-light conditions.

CONSTRUCTION FEATURES:

·         Tube Size  30 mm diameter.

·         Single-Piece Tube Maximizes alignment for improved accuracy and optimum visual performance, as well as ensures strength and waterproofness.

·         Aircraft-Grade Aluminum    Constructed from a solid block of aircraft-grade aluminum for strength and rigidity.

·         Waterproof O-ring seals prevent moisture, dust and debris from penetrating the riflescope for reliable performance in all environments.

·         Fog-proof  Nitrogen gas purging prevents internal fogging over a wide range of temperatures.

·         Shockproof Rugged construction withstands recoil and impact.

·         Hard Anodized Finish        Highly durable low-glare matte finish helps camouflage the shooter's position.

·         Capped Reset Turrets       Allow re-indexing of the turret to zero after sighting in the riflescope. Caps provide external protection for turret.

·         Adjustable Objective          Adjustment for riflescope's objective lens provides image focus and parallax removal.

SPECIFICATIONS:

·         Magnification         3-24x

·         Objective Lens Diameter    50 mm

·         Eye Relief  3.5 inches

·         Field of View          36.7-9.2 feet/100 yards

·         Tube Size  30 mm

·         Turret Style            Capped

·         Adjustment Graduation      1/4 MOA

·         Travel per Rotation 15 MOA

·         Max Elevation Adjustment  60 MOA

·         Max Windage Adjustment  60 MOA

·         Parallax Setting     10 yards to infinity

·         Length       14.3 inches

·         Weight       21.1 ounces

Comes with one piece quick detach picatinny mount pre-installed

ADDITIONAL INCLUDED PARTS:

·         ADJUSTABLE 6”-9” BIPOD WITH QUICK DETACH PICATINNY MOUNT

·         2 X 10 ROUND PMAG

 WARRANTY:

This firearm is covered by our lifetime warranty, please read full warranty statement for further details.

Please email your local FFL information to shipping@tacticalskeleton.com after placing your order.