BILLET UPPER

• US made in Scottsdale, Arizona
• T6061 billet
• 1913 picatinny rail flat top-DPMS low spec rail height
• manufactured from solid block of billet aluminum
• Brushed Camo Gun Metal Gray Cerakote
• slim profile shell deflector / forward assist
• 308 WIN engraved dust cover
• 6.5 CREEDMOOR engraved dust cover on CREEDMOOR upper

6.5 CREEDMOOR BARREL

• 24” MATCH GRADE straight fluted bull barrel
• 0.936” Gas Block
• RIFLE length gas tube
• Straight fluted for maximum heat dissipation
• 416R STAINLESS STEEL
• 5/8x24 muzzle thread pitch
• 1:8 TWIST
• M4 feed ramp

308 WIN BARREL

• 18” MATCH GRADE HBAR barrel
• 0.75” Gas Block
• MID LENGTH length gas tube
• 416R STAINLESS STEEL
• 5/8x24 muzzle thread pitch
• 1:10 TWIST
• M4 feed ramp

6.5 CREEDMOOR HANDGUARD

• 16.5” Super slim Handguard
• Brushed Camo Gun Metal Gray Cerakote
• T-markings on top rail
• Ultra-Light weight

308 WIN HANDGUARD

• 15” Super slim Handguard
• MLOK SYSTEM with three sectional rails installed
• Brushed Camo Gun Metal Gray Cerakote
• T-markings on top rail
• Ultra-Light weight

BOLT CARRIER GROUP

• Made for 7.62X51 / 308 Cal & 6.5 CREEDMOOR
• HPT/MPI Tested and Marked
• 9310 Hardened Steel Bolt
• 17-4 Stainless Steel Firing Pin (Heat treated to H900 Condition)
• 8620 carrier and gas key
• Hardened extractor S7 tool steel
• The group comes fully assembled with properly torqued and staked gas key
• Made in the USA

**  Nitride bolt carrier

(One BCG is included with the AR10 package)

6.5 CREEDMOOR MUZZLE BRAKE

• TANKER style
• TOP ports for MUZZLE CLIMB REDUCTION
• SIDE ports for RECOIL REDUCTION

308 WIN MUZZLE BRAKE

• Slip over sleeve style
• side ports for recoil reduction

BILLET LOWER RECEIVER

• Machined from 7075-T6 aircraft grade billet aluminum
• Matte black hard-coat anodized per Mil 8625 Type 3 Class 2
• Precision broached magazine well with beveled feed lips
• Machined and engraved to be compatible with 45 and 60-degree short throw fire control selectors.
• Caliber marking of “Multi” so it can be used with many different caliber uppers
• Compatible with all standard AR-10/.308 components and magazines and most aftermarket parts — Made to DPMS spec
• Upper tension screw behind grip screw (threaded hole with hardware included) to adjust any “slop” out of vertical fit between upper and lower
• Ambidextrous trigger finger rests with grooves (above and below mag release / mag catch)
• Brushed Camo Gun Metal Gray Cerakote
• Threaded bolt catch pin (Threaded hole and hardware)
• Integrated large opening “winter” trigger guard
• Manufactured to MILSPEC on state-of-the-art CNC equipment for consistent quality parts and exacting tolerances

STANDARD MILSPEC TRIGGER

LUTHAR MBA3 STOCK:

• Fully adjustable carbine buttstock assembly to mount to a carbine rifle (6-positions mil-spec or commercial tube) – this is our carbine stock
• additional 1″ height on cheek rest
• 3-axis adjustable butt plate assembly extends additional 1 1/16″ length of pull and includes the following movement:

1. horizontal for linear adjustment (i.e. length of pull)
2. vertical for a perfect butt plate fit into the curvature of the shoulder.
3. lateral adjustment for a ½ inch left or right cast
4. this butt plate assembly is interchangeable with the original mba-1 buttstock

• Includes a picatinny rail on the bottom rear of the stock body to attach your choice of many accessories
• Designed a flat bottom index set screw (10-24) to eliminate that constant rattle of carbine collapsible buttstock. this also allows you to secure the stock in your favorite position
• The black mba-3 comes with a medium soft rubber recoil pad, duro 85
• The LUTHAR mba-3 weighs roughly half that of comparable stocks coming in at just 18.5 ounces
• Fits all .223 and most .308 AR carbine style rifles
• Super strong glass filled nylon
• Easy to replace and quick to install
• Uses 4 out of the 6 positions on a mil-spec or commercial tube

FEATURES

• ergonomic
• adapts to existing commercial and mil-spec buffer tubes
• certain aftermarket commercial buffer tubes that exceed 1.172″ may not fit
• the vertical struts for the MBA 3 are fixed therefore the cheek pc is not reversible like the MBA 1 however the cheek piece itself is designed with a cheek pad for the lefty

44” Flight Case

• Made from tough light-weight polypropylene copolymer
• Has a rugged o-ring seal that makes it air and water tight up to 3ft deep
• Custom laser cut foam to hold all components of the system firm in place and provide maximum protection.
• Utilize an automatic pressure release valve so that it adjusts to its environment
• ATA/TSA ready for airline travel
• Lockable with comfort molded handles and spring loaded latches
• include heavy-duty off-road wheels and a second handle
• Made in the USA

Vortex Crossfire II 3-24x50 Scope

OPTICAL FEATURES

• Fully Multi-Coated  Increases light transmission with multiple anti-reflective coatings on all air-to-glass surfaces
• Second Focal Plane Reticle: Scale of reticle maintains the same ideally-sized appearance. Listed reticle sub tensions used for estimating range, holdover and wind drift correction are accurate at the highest magnification
• Illuminated Center Dot Provides a precise aiming point under low-light conditions

CONSTRUCTION FEATURES

• Tube Size  30 mm diameter
• Single-Piece Tube Maximizes alignment for improved accuracy and optimum visual performance, as well as ensures strength and waterproofness
• Aircraft-Grade Aluminum    Constructed from a solid block of aircraft-grade aluminum for strength and rigidity
• Waterproof O-ring seals prevent moisture, dust and debris from penetrating the riflescope for reliable performance in all environments
• Fog-proof  Nitrogen gas purging prevents internal fogging over a wide range of temperatures
• Shockproof Rugged construction withstands recoil and impact
• Hard Anodized Finish:  Highly durable low-glare matte finish helps camouflage the shooter's position
• Capped Reset Turrets:  Allow re-indexing of the turret to zero after sighting in the riflescope. Caps provide external protection for turret
• Adjustable Objective:  Adjustment for riflescope's objective lens provides image focus and parallax removal

SPECIFICATIONS

Comes with one piece quick detach picatinny mount pre-installed

ADDITIONAL INCLUDED PARTS

• ADJUSTABLE 6”-9” BIPOD WITH QUICK DETACH PICATINNY MOUNT
• 2 X 10 ROUND PMAG

WARRANTY

This firearm is covered by our lifetime warranty, please read full warranty statement for further details.

Please email your local FFL information to shipping@tacticalskeleton.com after placing your order.